Tag Archives: DIY

Featured Article #37: Introduction: Deciding on laying Carpet, Tile, or Hardwood floors?

Introduction: Deciding on laying Carpet, Tile, or Hardwood floors?

Home Improvement Basics & Practical Advice for your floor space

You may be surprised that you are capable of laying carpet, tile, or a hardwood floor.

My experience is rudimentary at best. Still I have been involved in all three of these types of floor projects. My intention is not to instruct on all of the elements of any one of these processes; but rather it is to give a basic understanding of what you can expect to encounter in laying floor: be it carpet, tile, or wood.

Laying Carpet

If you would like to carpet an area, my first suggestion is to just get it done professionally. They have the tools, the expertise, and the backs for it. Laying carpet is not fun work. However, in principal it is not the most difficult trade. Pulling up old carpet has more to do with grunt work than it does tools. You don’t need any expertise taking it out. Get a crowbar in under a place of the carpet, like where the carpet meets a vinyl or tile floor, or if you have to, where it meets the wall. Pry some carpet up and start pulling. Tack boards were placed around the borders of the room; these need to be pulled up too (don’t get poked by the tacks and nails). Scrape the floor clean of any areas where glue has particularly stuck the padding or carpet, or made rough places on the floor. Now the room is prepped for new carpet. New tack board strips must be laid down. These get nailed in with a good cement hammer. You will want to get further instruction for laying the carpet properly, but the idea is to measure well, roll it out and cut the angles, and with the right tools stretch and stick it into place. Again, pulling carpet was worth the savings but laying it is a whole new hassle.

Laying Tile

Tiling is easier than it would seem with the right tools (a good wet saw makes a lot of difference). Linoleum doesn’t even need to be pulled up. You mix the puddy to the right consistency; you cut tile as needed; you lay the tile and insert removable plastic dividers; and you grout it, wait for it to dry, and wipe it clean. You should lay the tile, having made necessary cuts, first. Before you’ve done any real damage you will already have a great idea of what your new floor is going to look like. If you have a toilet in the area you are tiling, you will want to remove the toilet and tile under it. This will make things a little trickier, but it will be satisfying to get the job done right with professional results. The beehive wax should be replaced to ensure no leaking occurs. It is not worth trying to salvage it for a cheap replacement. Look further into tiling; you can do this one.

Laying a Hardwood Floor

My least experience of the three types of floors is hardwood floors. I have never taken one out or put one in. But I have seen it done by a novice or two who were just reading the instructions off of the box.

Much of putting in a hardwood floor has to do with following directions. There are a few different patterns depending on the flooring you will be using. You will want to pay attention to the instructions given specifically for the materials you buy. Some wood flooring fits together by snapping in place while others mesh together. If you find you have to make several cuts to tailor the wood flooring to your needs, you are either covering a uniquely angled space or you are likely doing something wrong. You will want to place as much of the flooring in place as you would like to see it, before actually setting any of the wood flooring in place. If you do this, and cuts will need to be made, you will know where these need to be done first off. Adhesives that may be used in the process are very effective, so you will want to plan things out well. Ask your local Home Depot expert for advice on different wood floor installations.

A review of the overview

Again, my overview is only intended to give you a preview of what to expect. The first time you will want to solicit better step-by-step instructions. But if you have decided what would be perfect in the flooring space of your place, now you just have to decide if it is worth it to take on the challenge yourself, or if you should relinquish the job to the labors of the professionals. I have tried to give some insight into that decision.

All of these home improvements can be worth the expense—given the potential increase in the resale value—even during tough economic times. Just be sure to pick your project wisely. A fresh coat of paint on a wall, for example, brings in much more money than it costs, whereas repairing holes in walls is not usually a smart quick turn around type purchase. In review, tile goes a long ways for the effort. Wood floor goes farther but requires a little more doing. Both are worth the trouble. Carpeting, however, though often necessary, is not usually worth the do-it-yourself mentality.

Featured Article #33: Do-it-yourself Closet Organizer

Build Your Own Closet Organizer

By Chad Robert Parker

You’ve finally got that walk-in closet you’ve always wanted. Now that you can buy all the clothes and shoes you want (Or at least some of them), don’t spend all your money on the installation of a closet organizer. Do it yourself.

Seeing my own closet in disarray, I got online and looked at the possibilities of what is out there. The price range was anywhere from $200 to $500. What I saw was not elaborate or difficult. Seeing the boards on my office floor that I had discontinued plans for building some bookshelves with, I decided that I might just as easily put together a closet organizer for under $125. The boards’ cost just around $100, and then there was sandpaper, screws, stain (Honey gold to match the main bathroom cabinets, which I didn’t choose), a drip cloth, and a paintbrush to buy. I had an arm saw, a hammer, a screwdriver, and a drill already. I got online again and combined some ideas of what I had seen in other closet organizers. Pictured is what I came up with for my closet space, given the amount of wood I had for the job.

(Image here)

Then I got to work. How hard could it be? Well, the poplar boards had laid around long enough to warp some and the saw didn’t quite cut through the entire board widths, making for some unevenness. Weak screws required pre-drilling to keep from breaking off in the stiff boards. Staining the wood over a drip cloth in my garage while listening to the radio went smoothly enough though. With some effort the closet did come together. The neighbors only had to put up with the noise for one Saturday morning and a couple nights after work. All and all it was not too bad and I love the results.

The closet looks nice with its new dimensions. Plus, nicer clothes now have a place, not to mention my unmentionables having a closed in cabinet. And it is kind of fun to see the socks and shoes in their cubbyholes. The changes have definitely expanded my usable area of the closet and made it more orderly; it is both a functional and aesthetic design that fits my needs well.

Next up, my food storage pantry area needs some shelving. One more project before I take on any fine woodworking would probably be worthwhile anyway. I like the final result of the closet organizer, but I did learn that a finer finish would have required more sanding, a more even coat of stain, more notching to conceal screws, better screws (Pre-drilling and using a basic hand screwdriver instead of a power drill when working the screws into the wood sometimes was the best way to go), and a better saw to ensure good square cuts and fits. Can’t wait to build one of those laptop/food trays, or maybe a bedside table. Slowly working my way up, a little woodworking could really enhance my living standard, but I also learn my limits and will probably just opt to buy that office desk and hutch.